PM-4EX-G corner protection flattened end mills with straight shank and extra long cutting edge
High-performance general milling PM series
| Type | Basic dimension(mm) | Number of teeth Z | Geometry |
| | D | d | H | L | | |
| PM-4EX-D3.0-G | 3.0 | 6 | 20 | 75 | 4 | Picture 1 |
| PM-4EX-D4.0-G | 4.0 | 6 | 25 | 75 | 4 | Picture 1 |
| PM-4EX-D5.0-G | 5.0 | 6 | 30 | 75 | 4 | Picture 1 |
| PM-4EX-D6.0-G | 6.0 | 6 | 30 | 75 | 4 | Picture 2 |
| PM-4EX-D8.0-G | 8.0 | 8 | 40 | 100 | 4 | Picture 2 |
| PM-4EX-D10.0-G | 10.0 | 10 | 50 | 110 | 4 | Picture 2 |
| PM-4EX-D12.0-G | 12.0 | 12 | 50 | 110 | 4 | Picture 2 |
| PM-4EX-D16.0-G | 16.0 | 16 | 70 | 150 | 4 | Picture 2 |
| PM-4EX-D20.0-G | 20.0 | 20 | 75 | 150 | 4 | Picture 2 |
Detailed Product Description:
PM= High performance general machining
4EX= 4 flute corner protection flattened and extra long cutting edge
D3.0= Tool diameter 3.0mm
G=30 Degree taper 4-flute flattened end mills and long cutting edge
Number of teeth: 4 Flutes
End tooth type of mills: 4-flute sharp flattened end mills with straight shank and extra long cutting edge
Cutting diameter tolerance: D </= 12 (0~-0.020mm)
D<12 (0~-0.030mm)
Coated: NaNo AITiN coating
Helical angle: 30 degree
Machining operation: 
a. Side face: Flattened end mills for side machining
b. Step shoulder: Flattened end mills for shoulder machining
c. Straight slot: Flattened end mills for deep slot machining
Applicable workpiece material:
1. Very suitable for carbon steel , alloy steel, Pre-hardened steel ,hardened steel with 40HRC/50HRC/55HRC, cast iron, nodular cast iron
2. Suitable for stainless steel, Tianium alloy, heat resistant alloy
Advantage of high-performance general machining end mills
1. Optimized geometry, improves chip removal and chip forming with reduced cutting force.
2. Higher feed rates and improved metal removal rate for efficient machining, due to high stability of cutting edge and rigid tool structure.
Tool diameter: Ø6.0mm
Tool type: a) PM-4E-D6.0
b) Tool from overseas manufacturer
Machine tool: Mikron UCP 1000
Workpiece material: NAK80(40HRC)
Cooling system: air blow
Machining operation: side milling (down milling)
Cutting parameters: Vc=100m/min
ap=9mm, ae=0.6mm
Fz=0.4mm~0.16mm
3. With excellent wear resistance and toughness, high wear resistance and breakage resistance is achieved even during high performance milling.
Tool type: PM-4E-D6.0 Radial cutting depth: ae=0.6mm
Diameter: Ø6.0mm Cutting stype: side milling( down milling)
Workpiece material: NAK80(40HRC) Cooling system: air blow
Rotating speed: 5300r/min(100m/min) Machine tool: MIKRON UCP1000
Feed speed: 1696mm/min(0.32mm/r) Tool overhang: 22mm
Axial cutting depth: ap=9mm
Machining results
Conclusion: compared with other tools manufacturer, PM series has better breakage resistance.
The application status of PM-4E-D6.0-G in high speed milling.
Tool type: PM-4E-D6.0-G
Diameter: Ø6.0mm
Workpiece material: NAK80(40HRC) 
Rotating speed:13260r/min(250m/min)
Feed speed: 2652mm/min(0.2mm/r)
Axial cutting depth: ap=6mm
Radial cutting depth: ap=0.3mm
Cutting style: side milling( down milling)
Cooling system: air blow
Machine tool: MIKRON HSM800
Tool overhang: 22mm
High efficiency machining alloy steel of PM-4E-D8.0.
Machine tool: MIKRON UCP1000
Tool holder: HSK63-A Workpiece material: alloy steel
Cutting speed: 100(m/min)
Feed rate per tooth: 0.04(mm/tooth)
Axial cutting depth: 8(mm)
Radial cutting width(mm): changing, Maximum at full cutting
Cooling system: Emulsified liquid
Milling style: Contour following
Tool overhang: 30mm
End mills series of sharp and corner protection type
The characteristic of corner protection end mill:
1) It's suitable for bad cutting condition or hardness material machining.
2) High cutting edge strength and breakage resistance.
3) The degree of nose sharpness is reduced, the vestiage is left.
The characteristic of sharp end mill:
1) True 90 degree angle is obtained without material remaining in the corner.
2) The corner part is sharp, it is applicable in finishing or soft material machining. Especially, it is usually used in machining of non-ferrous material such as AI.
Two kind of cutting nose being used in side face milling of NAK80(40HRC)
Machine tool: MIKRON UCP1000
Tool holder: HSK63-A
Workpiece material: NAK80(40HRC)
Cutting speed: 100(m/min)(5300r/min)
Feed rate per tooth: 0.04-0.016(mm/tooth)
Axial cutting depth: 9(mm)
Radial cutting width: 0.6(mm)
Cooling system: air blow
Milling style: side milling ( down milling)
Tool overhang: 22(mm)
Tool abrasion when machining NAK80(HRC40)
Product Tags:
|
|
4- Flute Flattened Solid Carbide End Mills PM - 4EX - G Series NaNo TiAIN Images
|
